en:sim:manual:jak_na_instalaci

Connection Diagram

Anonymous (anonymous@undisclosed.example.com) — 2015-02-17T12:10:31+00:00

Connection Diagram ---------- AEG communication card Connection to SM2-MU via communication card terminals AEG SM2-MU T+ A T- B R+ Y R- Z Connection to SM2-MU via RJ45 connector. In case of the involvement of multiple inverters, connect the inverters with straight cable.

Connection Diagram

Anonymous (anonymous@undisclosed.example.com) — 2020-04-21T17:36:10+00:00

Connection Diagram ---------- Aurora RS485 Connection to SM2-MU Aurora SM2-MU +T/R A -T/R B RTN SGND In case of the involvement of multiple inverters, connect the inverters each other this way: Inverter 1 Inverter 2

Connection Diagram

Anonymous (anonymous@undisclosed.example.com) — 2015-02-17T12:32:25+00:00

Connection Diagram ---------- Connection Danfoss to SM2-MU In case of the involvement of multiple inverters, connect the inverters with straight cable. A terminator is connected at the last output of the inverter. << Back

Connection Diagram

Anonymous (anonymous@undisclosed.example.com) — 2015-02-17T12:54:26+00:00

Connection Diagram ---------- Connection Delta to SM2-MU In case of the involvement of multiple inverters, connect the inverters with straight cable. A terminator is connected at the last output of the inverter. << Back

Connection Diagram

Anonymous (anonymous@undisclosed.example.com) — 2014-10-03T13:50:53+00:00

Connection Diagram ---------- In case of the involvement of multiple inverters, connect the inverters each other this way: Inverter 1 Inverter 2 A A B B Shield Shield Configuration Notes << Back

Digital Inputs and Outputs

Anonymous (anonymous@undisclosed.example.com) — 2018-07-10T14:41:01+00:00

Digital Inputs and Outputs ---------- Inputs Solar Monitor has 3 digital inputs DI. It is easy to connect movement sensor, surge, optical barrier, door sensor and various other devices that use contact inputs to indicate its status. Any of the inputs DI1, DI2, DI3 can be used for measuring energy at the

Connecting to the Electrometer

Anonymous (anonymous@undisclosed.example.com) — 2019-12-06T10:57:25+00:00

Connecting to the Electrometer ---------- Installation Solar Monitor can be connected to Green Bonus electro meter via any of three binary inputs DI. It reads the energy output of your PV plant. The following picture shows how to connect to the electro meter with S0 (puls) output:

Connection Diagram

Anonymous (anonymous@undisclosed.example.com) — 2015-02-17T13:02:34+00:00

Connection Diagram ---------- Connection Fronius to SM2-MU In a similar way, you can connect SM2 to connector OUT. Then terminator is connected to IN at the end of the bus (apply either when connecting to one inverter). In case of the involvement of multiple inverters, connect the inverters with straight cable.

Connection Diagram

Anonymous (anonymous@undisclosed.example.com) — 2014-09-29T13:25:33+00:00

Connection Diagram ---------- In case of the involvement of multiple inverters, connect the inverters each other this way: Inverter 1 Inverter 2 A A B B On the last inverter is necessary to turn on or off the termination „TERM

Mechanical Fastening

Anonymous (anonymous@undisclosed.example.com) — 2014-08-26T12:54:49+00:00

Mechanical Fastening ---------- Solar Monitor unit is designed for indoor installation. When placed outdoor it needs sufficient protection from external influences and respecting operational temperature range is essential. You will find the data in the chapter

Connection Diagram

Anonymous (anonymous@undisclosed.example.com) — 2018-04-20T10:57:27+00:00

Connection Diagram ---------- Connection Omnik to SM2-MU << Back

Connection Diagram

Anonymous (anonymous@undisclosed.example.com) — 2014-09-30T09:43:47+00:00

Connection Diagram ---------- In case of the involvement of multiple inverters, connect the inverters each other this way: Inverter 1 Inverter 2 6:GO 6:GO B+ B+ A- A- On the last inverter is necessary to turn on or off the termination. Termination Enabled = terminals 9+10 connected.

Power Supply Connection

Anonymous (anonymous@undisclosed.example.com) — 2014-08-26T08:51:16+00:00

Power Supply Connection ---------- Source at the DIN rail Socket adaptor

Sensors

Anonymous (anonymous@undisclosed.example.com) — 2014-08-26T12:58:51+00:00

Sensors ---------- Solar Monitor unit can connect up to 10 sensors. Maximum length of cables must not exceed 100 meters. Following sensors with cables can be connected. In case of multiple sensors use parallel connection into the same terminal.

Connection Diagram

Anonymous (anonymous@undisclosed.example.com) — 2015-02-17T13:16:35+00:00

Connection Diagram ---------- Connection Schneider to SM2-MU In case of the involvement of multiple inverters, connect the inverters with straight cable. Set the termination on the last communication card (both DIP switches to same position)

Local Area Network (LAN)

Anonymous (anonymous@undisclosed.example.com) — 2014-08-25T14:22:59+00:00

Local Area Network (LAN) ---------- In order to communicate with the user, Solar Monitor must be connected to ethernet (LAN). There is one port RJ-45 available, the same as in PC's. The unit is connected to the net in the same way as PC. Connect the unit into

Connection Diagram

Anonymous (anonymous@undisclosed.example.com) — 2014-09-30T14:10:07+00:00

Connection Diagram ---------- In case of the involvement of multiple inverters, connect the inverters with straight cable. If needed fit jumper „A“ as terminator on the last inverter (near communication card). << Back

Connection Diagram

Anonymous (anonymous@undisclosed.example.com) — 2015-02-17T13:25:18+00:00

Connection Diagram ---------- Connection Solar Max to SM2-MU In case of the involvement of multiple inverters, connect the inverters with straight cable. Configuration Notes << Back

Connection Diagram

Anonymous (anonymous@undisclosed.example.com) — 2018-05-25T15:21:24+00:00

Connection Diagram 1a) SM2-MU – master for all devices For power supply see Power Supply section. All individual Taroms connected as slaves - data are read from each device. 1b) Multiple Tarom 6000-M on a single RS485 bus 1a) and 1b) can be mixed

Inverters

Anonymous (anonymous@undisclosed.example.com) — 2019-09-30T11:52:36+00:00

Inverters ---------- Terminals SM2-MU: A, B, SGND, Z, Y, or DC+ a DC - are used according to the inverter manufacturer. If there is SM at the beginning of H-bus, sliding switches must be in ON position. The same for the inverter - if it supports bus termination, the last one should be switched on according to the manufacturer's instructions. Description of inverter connection to the Solar Monitor unit and whether it supports the bus is to be found in the following tab…

Connection Diagram

Anonymous (anonymous@undisclosed.example.com) — 2018-03-22T00:05:15+00:00

Connection Diagram Detection << Back

Connection Diagram

Anonymous (anonymous@undisclosed.example.com) — 2015-02-17T13:48:46+00:00

Connection Diagram ---------- Connection Sungrow to SM2-MU In case of the involvement of multiple inverters, connect the inverters with straight cable. A terminator is connected at the last output of the inverter. Configuration Notes

Connection Diagram

Anonymous (anonymous@undisclosed.example.com) — 2015-02-17T14:01:07+00:00

Connection Diagram ---------- Connection Sunwille to SM2-MU In case of the involvement of multiple inverters, connect the inverters with straight cable. Set the termination on the last communication card (both DIP switches to same position)